Plumbing Basics: Your Key to Installing a Bathtub
Plumbing Basics: Your Key to Installing a Bathtub
Blog Article
They are making a number of good observations related to Tools You Need to Install a New Bathtub as a whole in this great article following next.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Mounting a bathtub isn't exactly rocket science, but it does require strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old tub with a new one is likewise a moderately challenging project. If the old bathtub is conveniently obtainable, the job can move immediately; if you need to open up a wall surface to remove the old tub and place the new bathtub, the task is much harder. In either instance, the job is within a residence handyman's abilities, although you will need an assistant to move out the old bathtub and set in the brand-new one. Ensure you have actually qualified yourself for the work and fit trying it. Rather than employing a contractor to take over a halfway-completed project, it is much better to take into consideration utilizing one before you begin. Possibilities are you may require an expert plumber to make tube connections.
This article will help you install a brand-new bath tub in your bathroom if you have currently gotten a new tub and also don't require to alter the arrangement of your previous water supply pipes.
Your devices and also material checklist need to consist of the following:
Preparing for the Installment
To start with, the supporting framework provided with the bath needs to be fitted (if required) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to ensure that if the faucet comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to prevent pressure on the bath tub.
Fit the versatile tap ports to the bottom of the two faucets utilizing 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you use all of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be suited its final setting.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installment, then the first thing you must do is disconnect the water system. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The procedure of removing the existing taps can be fairly troublesome due to the restricted accessibility that is typically the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the faucets. Have a fabric all set for the continuing to be water that will originate from the pipelines. When the supply pipelines have been gotten rid of, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning during this process. When the faucets have been removed, the holes in the bath/basin will need to be cleaned of any old sealing substance.
Prior to carrying on to fit the new faucets, contrast the pipe links on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new faucets to fit.
Installing the Tub
Using the two wood boards under its feet, place the bathtub in the required placement. The wood boards are practical in evenly spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four tiny factors.
The next objective is to make sure that the bath tub is leveled all round. This can be attained by checking the level and also adjusting the feet on the tub till the level checks out degree.
To mount faucets, fit the bottom of the furthest versatile faucet adapter to the ideal supply pipe by making a compression join; then do the same for the other tap.
Switch on the water system as well as inspect all joints and brand-new pipework for leakages as well as tighten them if necessary. Load the tub as well as additionally examine the overflow electrical outlet as well as the normal outlet for leaks.
Ultimately, deal with the bath paneling as described in the supplier's user's manual. Tiling as well as securing around the bath tub should wait till the tub has been made use of a minimum of when as this will resolve it right into its final setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end provides a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the placing opening in the bath/basin guaranteeing that the washers are in area in between the tap as well as the sink. Protect the faucet in place with the supplier provided backnut. As soon as the faucet is firmly in position, the supply pipes can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular faucet connectors. The former type ought to be linked to the tap finishes first, tightening up just by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the location where the bathroom fulfills the tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to break a stiff seal, triggering the water to penetrate the wall in between the bath and the tiling, bring about issues with wetness as well as possible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your components as well as fittings. They are marketed in tubes as well as cartridges, and also can sealing voids up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always fill the bathtub with water before sealing, to allow for the motion experienced when the bathtub is in usage. The sealant can split rather early if you do not take into account this activity before sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise quickly offered on the market. It is recommended to fit the ceramic tiles using water-resistant or water resistant sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed our piece on Installing A Bathtub. Thanks so much for taking the time to read through our piece. Are you aware of someone else who is serious about the niche? Do not hesitate to share it. We value reading our article about Installing A Bathtub.
For quick fixes, call! Report this page